[Oct 19, 2021] NS0-173 Dumps Full Questions - Exam Study Guide
Cisco and NetApp FlexPod Free Certification Exam Material from Exam4Tests with 62 Questions
NEW QUESTION 23
Click the Exhibit button.
You are designing a FlexPod Datacenter solution for Microsoft Windows 2012 with Hyper-V. All hosts will boot from the SAN, including management hosts. The management hosts are Cisco C-Series servers.
Referring to the exhibit, which adapters are required to boot the management servers from the SAN?
- A. two 1GbE NICs
- B. two 10GbE NICs
- C. two 10GbE CNAs
- D. two 8Gb HBAs
Answer: B
NEW QUESTION 24
A customer has several existing standalone Cisco UCS C-Series servers that they would like to repurpose and add to their FlexPod Datacenter solution.
Which action should the customer perform on these servers before using UCS Manager?
- A. Zero-out the FlexFlash cards on each server.
- B. Reboot the CIMC on each server.
- C. Remove the hard disks on each server.
- D. Reset the CIMC to the factory settings on each server.
Answer: D
Explanation:
On rare occasions, such as an issue with the current running firmware, troubleshooting a server may require you to reset the CIMC to the factory default. When this happens, all user-configurable settings are reset. This procedure is not part of the normal server maintenance. After you reset the CIMC, you are logged off and must log in again. You may also lose connectivity and may need to reconfigure the network settings.
NEW QUESTION 25
A customer is evaluating management tools for a new FlexPod infrastructure. They desire a tool that can orchestrate the provisioning of UCS compute nodes, NetApp storage, and VMware networking.
Which tool satisfies the requirements of this customer's heterogeneous environment?
- A. NetApp OnCommand Unified Manager
- B. UCS Central
- C. UCS Director
- D. NetApp OnCommand Insight
Answer: C
NEW QUESTION 26
A service provider is designing a FlexPod configuration to host multiple customers in a hybrid cloud environment, where IP address-range conflicts might arise on the shared storage.
Which NetApp feature should be enabled to prevent these conflicts?
- A. IPspaces
- B. failover groups
- C. SVMs
- D. broadcast domains
Answer: A
NEW QUESTION 27
You are asked to design a FlexPod solution with a Cisco UCS B-Series chassis. There is no requirement for any Cisco UCS C-Series rack servers. You must ensure that there is a minimum of a 2500 VLAN or VSAN capacity per UCS domain.
In this scenario, which Cisco Fabric Interconnects do you select?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION 28
Which Cisco Nexus series switch supports NX-OS standalone mode or Application Centric Infrastructure (ACI) fabric mode?
- A. Nexus 7000
- B. Nexus 5000
- C. Nexus 3000
- D. Nexus 9000
Answer: D
NEW QUESTION 29
You are configuring Cisco UCS servers for FC SAN boot and want to perform zoning on your Cisco Nexus 5000 series switches.
In this scenario, which statement is correct?
- A. SAN links are required between the Cisco Fabric Interconnects and the Nexus 5000 switches.
- B. FC zoning on the Nexus series switches is not supported; zoning can be done only on the Cisco Fabric Interconnects.
- C. An iSCSI license on the NetApp storage controller is required.
- D. The corresponding FC ports on your NetApp storage array must be configured in LACP mode.
Answer: B
NEW QUESTION 30
Your customer has a FlexPod solution with a 2-node switchless ONTAP system, Cisco Nexus 93108 switches, and Cisco UCS B-Series servers. The customer wants to expand to a 4-node ONTAP storage cluster.
Which configuration is valid for expansion?
- A. Add one Nexus 3232C switch for the cluster interconnect.
- B. Add two Nexus 3232C switches for the cluster interconnect.
- C. Use the existing Nexus 93108 switches for the cluster interconnect.
- D. Add two Nexus 93108 switches for the cluster interconnect.
Answer: B
NEW QUESTION 31
Click the Exhibit button.
A customer wants to ensure that FlexPod Datacenter connections to the storage layer are highly available. Which two configurations shown in the exhibit satisfy the customer's requirements? (Choose two.)
- A. III.
- B. IV
- C. I.
- D. II.
Answer: A,B
NEW QUESTION 32
After you install a FlexPod infrastructure at a customer site, you need to migrate the existing Vmware virtual machines off the infrastructure that was used before FlexPod was installed.
Which VMware vSphere feature accomplishes this task?
- A. vSphere HA
- B. vSphere DRS
- C. vMotion
- D. VM Component Protection
Answer: C
NEW QUESTION 33
You are configuring high availability within the network layer of your FlexPod configuration.
In this scenario, what are two Cisco best practices for designing vPC on your Cisco 9000 Series switches?
(Choose two.)
- A. Port channels should be configured for LACP passive mode.
- B. Peer keep-alive connectivity between the switches should be established.
- C. A minimum of four 10GB Ethernet connections are required for vPC.
- D. The vPC auto-recovery feature should be enabled.
Answer: B,C
Explanation:
vPC also relies on the periodic keepalive messages to determine when one of the connected devices on the peer link fails.
vPC peer link - The link used to synchronize states between the vPC peer devices. Both ends must be on 10- Gigabit Ethernet or 40-Gigabit Ethernet interfaces.
Reference:
configuration/guide/b_Cisco_Nexus_9000_Series_NX-OS_Interfaces_Configuration_Guide/ b_Cisco_Nexus_9000_Series_NX-OS_Interfaces_Configuration_Guide_chapter_0111.html
NEW QUESTION 34
A customer wants to configure SAN boot for its FlexPod system. The customer must consider the minimum number of FC ports to be configured on each node in the ONTAP storage solution.
In this scenario, what is the minimum number of FC ports that should be configured per storage node?
- A. three
- B. two
- C. four
- D. one
Answer: A
NEW QUESTION 35
A customer is planning to deploy a FlexPod solution for a large scale SAN requirement that uses the FC protocol. The customer plans to use Smart Zoning in the configurations to reduce the number of TCAM entries in the zoning process.
In this scenario, which design would enable the customer to use Smart Zoning?
- A. storage connected to Cisco Nexus 9000 Series switches
- B. storage directly connected to Cisco UCS Fabric Interconnects
- C. storage connected to Cisco MDS switches
- D. storage connected to Cisco Nexus 5000 Series switches
Answer: C
NEW QUESTION 36
Which port type would you configure when you connect a chassis to the Cisco Fabric Interconnects?
- A. FC storage ports
- B. Ethernet uplink ports
- C. appliance ports
- D. server ports
Answer: A
NEW QUESTION 37
Click the Exhibit button.
The total number of servers that a Cisco UCS Mini chassis supports is set to a maximum of how many hosts as shown in the exhibit?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION 38
A customer is investigating options for implementing a FlexPod Datacenter solution that is using vSphere 6.x.
In this scenario, which two resources would be important to review? (Choose two.)
- A. Cisco Validated Design documents
- B. NetApp Technical Report
- C. Cisco Cloud Center documentation
- D. VMware vSAN documentation
Answer: A,B
NEW QUESTION 39
A customer wants to deploy a FlexPod solution that involves directly connecting the NetApp AFF storage using the FCoE protocol to the Cisco UCS Fabric Interconnects.
In this scenario, which Cisco UCS Fibre Channel mode would be used to accomplish this task?
- A. access mode
- B. switching mode
- C. end host mode
- D. trunk mode
Answer: B
NEW QUESTION 40
......
Dumps Brief Outline Of The NS0-173 Exam: https://www.exam4tests.com/NS0-173-valid-braindumps.html