Ultimate Guide to the D-PDC-DY-23 - Latest Nov 14, 2024 Edition Available Now
2024 Updated Verified Pass D-PDC-DY-23 Exam - Real Questions and Answers
NEW QUESTION # 67
A network administrator has to configure a virtual IP address using VRRP on interface VLAN 100 within OS10.
What are the correct steps to accomplish this?
- A. OS10(config)# interface vlan 100
OS10(conf-if-vl-100)# ip address 10.0.100.2/24
OS10(conf-if-vl-100)# standby-group 250
OS10(conf-vlan100-vrid-250)# virtual-address 10.0.100.1 - B. OS10(config)# interface vlan 100
OS10(conf-if-vl-100)# ip address 10.0.100.1/24
OS10(conf-if-vl-100)# vrrp-group 250
OS10(conf-vlan100-vrid-250)# virtual-address 10.0.100.2 - C. OS10(config)# interface vlan 100
OS10(conf-if-vl-100)# ip address 10.0.100.2/24
OS10(conf-if-vl-100)# vrrp-group 256
OS10(conf-vlan100-vrid-256)# virtual-address 10.0.100.1 - D. OS10(config)# interface vlan 100
OS10(conf-if-vl-100)# ip address 10.0.100.1/24
OS10(conf-if-vl-100)# standby-group 256
OS10(conf-vlan100-vrid-256)# standby-address 10.0.100.2
Answer: B
NEW QUESTION # 68
When configuring UFD, which command is op tonal?
- A. name
- B. enable
- C. uplink-state-group
- D. upstream
Answer: A
NEW QUESTION # 69
When using Policy-Based Routing, what is a valid action?
- A. Drop packet
- B. Set 802.1Q VLAN ID
- C. Set source IP address
- D. Set destination TCP port number
Answer: A
NEW QUESTION # 70
Which command mode allows configuration of switches L2 and L3 interfaces?
- A. Interface
- B. EXEC Mode
- C. Global
- D. Configuration
Answer: A
NEW QUESTION # 71
A network administrator has recently configured eBGP to use source addressing from its loopback interfaces. Customers later report that eBGP routes are not being learned.
What could be the cause of this issue?
- A. BGP devices must be configured with the multihop command when using loopback interfaces
- B. The network administrator neglected to issue the no shutdown command to bring the loopback interface online
- C. BGPv4 does not support the use of loopback interfaces
- D. BGP devices must be configured to use source addressing from its physical interfaces only
Answer: A
NEW QUESTION # 72
What are the correct commands that configure the DHCP lease from pool DC1 to never expire?
- A. OS10(config)# ip dhcp server OS10(config-dhcp)# pool DC1 accounting OS10(config-dhcp-DC1)#no lease expire
- B. OS10(config)# ip dhcp server OS10(config-dhcp)# pool DC1 accounting OS10(config-dhcp-DC1)# no expire
- C. OS10(config)#dhcp server OS10(config-dhcp)# pool DC1 OS10(config-dhcp-DC1)# no lease expire
- D. OS10(config)# ip dhcp server OS10(config-dhcp)# pool DC1 OS10(config-dhcp-DC1)#lease infinite
Answer: D
NEW QUESTION # 73
What is one of the configuration requirements for VLT on OS10?
- A. Configure a time interval to delay bringing up VLT ports after reload when the VLTi is turned on after failure.
- B. Create a VLT domain on each peer using the vlt-domain command.
- C. Configure a port channel for VLTi
- D. Manually reconfigure the VLT MAC address. Configure the VLT MAC address on both VLT peers.
Answer: B
NEW QUESTION # 74
What is the function of UFD?
- A. Load balances upstream activity.
- B. Prevents the loss of upstream activity.
- C. Detects the loss of downstream activity.
- D. Detects the loss of upstream activity.
Answer: D
NEW QUESTION # 75
A network administrator is troubleshooting VLT behavior where all VLT port channels are down on both VLT peers.
What type of mismatch can cause this issue?
- A. Spanning-tree mismatch at global level
- B. Spanning-tree mismatch at port level
- C. System MAC mismatch
- D. VLT LAG ID mismatch
Answer: A
NEW QUESTION # 76
The VLAN tag is located between which fields in the Ethernet frame?
- A. Ether Type/Size and Data
- B. Preamble and Destination MAC
- C. Destination MAC and Source MAC
- D. Source MAC and Ether Type/Size
Answer: D
NEW QUESTION # 77
A customer has disabled LLDP on the management interface of the switch.
What is the proper command to re- enable it?
- A. OS10(config)# interface mgmt 1/1/1
OS10(conf-if-ma-1/1/1)#lldp med enable
OS10(conf-if-ma-1/1/1)#lldp timer 10 - B. OS10(config)# interface mgmt 1/1/1
OS10(conf-if-ma-1/1/1)#lldp transmit
OS10(conf-if-ma-1/1/1)#lldp receive - C. OS10(config)# interface mgmt 1/1/1
OS10(conf-if-ma-1/1/1)#lldp tly-select
OS10(conf-if-ma-1/1/1)#lldp dot1tlv - D. OS10(config)# lldp enable OS10(config)#lldp transmit OS10(config)#lldp receive
Answer: B
NEW QUESTION # 78
Interface Ethernet 1/1/3 has been configured with an IP address, and the interface is UP.
How does the routing table present the associated network?
- A. Directly connected
- B. Static
- C. Dynamic
- D. Default
Answer: A
NEW QUESTION # 79
Which QoS model can provide quality of service in a routed network environment?
- A. CoS
- B. LIFO
- C. FIFO
- D. DSCP
Answer: D
NEW QUESTION # 80
When installing OS10 on a switch from a USB drive, what format is used for the file system?
- A. NTFS
- B. HFS
- C. HFS+
- D. FAT32
Answer: D
NEW QUESTION # 81
Match the IGMP versions and features in the source column to the feature or version where they first appeared. There are more packet descriptions than IGMP versions.
- A. IGMP Version 1 - a) Queries can be sent out either as general queries or group-specific queries IGMP Version 2 - b) IGMP Version 3 IGMP Version 2 - c) Routers send out a 'query' every 60 seconds Exclude Mode - e) Enhances by adding Source-Based-Filtering
- B. IGMP Version 1 - c) Routers send out a 'query' every 60 seconds
IGMP Version 2 - b) IGMP Version 3
IGMP Version 2 - d) IGMP Version 2
Exclude Mode - e) Enhances by adding Source-Based-Filtering - C. IGMP Version 1 - a) Queries can be sent out either as general queries or group-specific queries IGMP Version 2 - b) IGMP Version 3 IGMP Version 2 - d) IGMP Version 2 Exclude Mode - e) Enhances by adding Source-Based-Filtering
- D. IGMP Version 1 - c) Routers send out a 'query' every 60 seconds
IGMP Version 2 - b) IGMP Version 3
IGMP Version 2 - d) IGMP Version 2
Exclude Mode - a) Queries can be sent out either as general queries or group-specific queries
Answer: A
NEW QUESTION # 82
In a PIM Sparse Mode (PIM-SM) based multicast topology, what function does the Rendezvous Point provide?
- A. The node is used to provide IGMP snooping on a layer 2 shared segment.
- B. The root node of the shared tree topology is used to provide routing between the source and receiver.
- C. The node is used to provide IGMP snooping across a layer 3 boundary.
- D. The root node of the source tree topology is used to provide routing between the source and receiver.
Answer: B
NEW QUESTION # 83
How are multiple hardware based ACLs filtered?
- A. IP
- B. NTP
- C. DHCP
- D. NPU
Answer: D
NEW QUESTION # 84
Which two commands can be used to setup as which for remote management over an on-default VRF? (Select 2)
- A. modo management
- B. ip vrf management
- C. mode L3
- D. management route 2::/ 64 managementethernet.
- E. ip vrf forwarding vrf-management
Answer: D,E
NEW QUESTION # 85
What is a characteristic of a static LAG on a Dell Networking OS10 switch?
- A. Uses LACP for configuration only
- B. Does not use any protocol for configuration and management
- C. Uses LACP for management only
- D. Does not allow reconfiguration of the predefined ports
Answer: B
NEW QUESTION # 86
A network administrator wants to limit the amount of bandwidth that video traffic can consume.
Which type of policy map should be used?
- A. It is not possible to limit bandwidth using policy maps
- B. Control plane
- C. Queuing
- D. Application
Answer: C
NEW QUESTION # 87
......
Dumps Moneyack Guarantee - D-PDC-DY-23 Dumps Approved Dumps: https://www.exam4tests.com/D-PDC-DY-23-valid-braindumps.html
Verified D-PDC-DY-23 Exam Dumps PDF [2024] Access using Exam4Tests: https://drive.google.com/open?id=10-7jIPyWQkDs2Nc7vuylvAEPF-So-pdF