2023 Correct Practice Tests of CQE Dumps with Practice Exam
Certification Sample Questions of CQE Dumps With 100% Exam Passing Guarantee
NEW QUESTION 60
Two advantages of process mapping are the ability to
I. Visualize the process being described.
II. Discover manufacturing problems only.
III. Discover quality problems only.
IV. Check current processes for duplication or redundancy.
- A. I and III only
- B. II and III only
- C. II and IV only
- D. I and IV only
Answer: D
NEW QUESTION 61
Regardless of the distribution of the individuals, the distribution of the average of n samples will follow which distribution as n becomes large?
- A. Exponential.
- B. Lognormal.
- C. Poisson.
- D. Normal
Answer: D
NEW QUESTION 62
The failure rate model above is used to show a typical relationship of many parts between their failure rate and the time in service. The reliability function for period "B" is BEST represented by
- A. Option C
- B. Option A
- C. Option B
- D. Option D
Answer: D
NEW QUESTION 63
What is the standard deviation of the values below?
4.5, 5.1, 6.2, 2.1, 3.9
- A. 1.362
- B. 2.087
- C. 1.522
- D. 1.136
Answer: A
NEW QUESTION 64
What is the standard deviation of the following data?
3.2, 3.1, 3.3, 3.3, 3.1
- A. 0.1
- B. 0.0498
- C. 3.2
- D. 0.0894
Answer: D
NEW QUESTION 65
Which of the following quality gurus was very critical of merit-pay and individual bonuses?
He discouraged management by objectives and the ranking of employees by performance.
- A. Dr. Taguchi
- B. Dr. Juran
- C. Dr. Feigenbaum
- D. Dr. Deming
Answer: D
NEW QUESTION 66
Applications for surface plate includes which of the following?
. Referencing plane for length measurements.
. Referencing plane for parallelism measurements.
. Establishing a datum plane for dimensional layout.
. Waiting place for delicate parts.
. Keeping extra gages when not in use.
- A. I andIVonly
- B. I andIIonly
- C. I,IIandIIIonly
- D. IIIand V only
Answer: C
NEW QUESTION 67
To be effective, a corrective and preventive action system must have
- A. A method for identifying nonconformities.
- B. A material review board.
- C. Approved of the QC department.
- D. Top management support.
Answer: A
NEW QUESTION 68
Maintainability is
- A. The probability of a system being restored to functional operation within a given period of time.
- B. Performing adequate maintenance on a system.
- C. Probability of survival of a system for a given period of time.
- D. Maintaining a machine in satisfactory working condition.
Answer: A
NEW QUESTION 69
Which of the following is the BEST statement to make regarding the relationship between product precision and product production?
- A. With too much precision, production costs increase.
- B. Precision costs and performance are related.
- C. With too little precision, production costs increase.
- D. With little precision, performance will improve.
Answer: B
Explanation:
Explanation/Reference:
NEW QUESTION 70
The example of a supplier's quality management effort to meet your existing contractual requirements is MOST like
. A product audit.
. A process audit.
. A system audit.
- A. IIonly
- B. I,IIandIII
- C. I andIIonly
- D. IIIonly
Answer: D
NEW QUESTION 71
The probability of an accident for the head event "H" given below is:
- A. 0.0689
- B. 0.1125
- C. 0.1100
- D. 0.0700
Answer: A
NEW QUESTION 72
The distribution of a characteristic is negatively skewed. The sampling distribution of the mean for large samples is:
- A. Approximately normal.
- B. Lognormal.
- C. Negatively skewed.
- D. Positively skewed.
Answer: A
NEW QUESTION 73
A purchase order for subassemblies classified as critical must include a review by
. Quality engineering.
. The procurement department.
. Design engineering.
- A. IIandIIIonly
- B. IIIonly
- C. I andIIIonly
- D. I,IIandIII
Answer: D
NEW QUESTION 74
Failure mode, effect, and criticality analysis, (FMECA) is primarily for the purpose of
- A. Determining the cause of a failure, by dissecting the item, to help obtain corrective action.
- B. Determining, by extensive analysis, the reliability of an item.
- C. Learning as much about the item as possible after qualification test.
- D. Determining the way an item will most likely fail to help obtain design and procedural safeguards against such failures.
Answer: D
NEW QUESTION 75
An X-bar and R chart with n=5 has been plotted for some time and has demonstrated random variation.
Upon review of the last 30 plot points, the expected number of runs around the centerline on the X-bar chart is expected to be approximately which of the following?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION 76
The primary reason that nonconforming material should be identified and segregated is
- A. To obtain samples of poor workmanship for use in the company's training program.
- B. So that the cause of nonconformity can be determined.
- C. So that responsibility can be determined and disciplinary action taken.
- D. So it cannot be used in production without proper authorization.
Answer: D
NEW QUESTION 77
Periodically, a sample of 20 items are randomly selected from a population that is normally distributed, the average is computed, and plotted. Which of the following statements is correct?
I. The average of the logarithms of the values is lognormally distributed.
II. The standard deviation of the averages is equal to the standard deviation of the individuals divided by the square root of 20.
III. The variance of the averages is equal to the variance of the individuals divided by the square root of 20.
- A. I and III only
- B. II only
- C. I only
- D. I and II only
Answer: B
NEW QUESTION 78
The MOST essential value of a surface plate in precision measurement application is which of the following?
- A. It provides an accurate reference surface.
- B. It provides a flat working surface.
- C. It provides a chemically resistant work surface.
- D. It provides a surface free of minor vibration.
Answer: A
NEW QUESTION 79
A normal (Gaussian) distribution curve is
- A. Pear shaped.
- B. Bell shaped.
- C. Dome shaped.
- D. Positively skewed.
Answer: B
NEW QUESTION 80
The Dodge-Romig tables are designed to minimize which of the following parameters?
- A. AOQ
- B. ATI
- C. AOQL
- D. AQL
Answer: B
NEW QUESTION 81
The first and most important step, in establishing a good corporate quality plan is
- A. Determining customer requirements.
- B. Evaluation vendor quality systems.
- C. Ensuring quality participation in design review.
- D. Determining manufacturing process capabilities.
Answer: A
NEW QUESTION 82
The steeper the OC-curve, the
- A. The smaller the sample size.
- B. The lower the AQL.
- C. Less protection for both producer and consumer.
- D. More protection for both producer and consumer.
Answer: D
NEW QUESTION 83
The Shewhart or Deming cycle is often referred to as
- A. The cause and effect diagram.
- B. Problem solving flow chart.
- C. The affinity diagram.
- D. Plan-do-check-act.
Answer: D
NEW QUESTION 84
......
CQE Sample Practice Exam Questions 2023 Updated Verified: https://www.exam4tests.com/CQE-valid-braindumps.html
Pass Key features of CQE Course with Updated 162 Questions: https://drive.google.com/open?id=1QnXFJ2H_zLA7hsi3n_zZ-VwsXB6HeyNi