ASQ New 2023 CQE Sample Questions Reliable CQE Test Engine
Feel ASQ CQE Dumps PDF Will likely be The best Option
NEW QUESTION 61
The ideal results of a quality training effort would NOT include which of the following?
- A. Reduced defects and employee turn-over.
- B. Increased cost-of-quality results.
- C. Increased productivity and job satisfaction.
- D. Improved working methods and morale.
Answer: B
NEW QUESTION 62
Which of the following control charts are more efficient than an X-bar chart at detecting small shifts in the mean?
I. CUSUM.
II. EWQR.
III. EWMA.
- A. I and III only
- B. III only
- C. I only
- D. II only
Answer: A
NEW QUESTION 63
Which of the following quantitative methods does NOT apply to the assessment of actual system/component reliability?
- A. Analysis of results of reliability demonstration tests.
- B. Evaluation of laboratory test data.
- C. Statistical allocation of reliability goals.
- D. Statistical analysis of field test and failure data.
Answer: C
NEW QUESTION 64
Measurement gaging is preferable to go, no-go gaging of a quality characteristic because
- A. It is more scientific.
- B. It provides the most information per piece inspected.
- C. It requires greater skills.
- D. It requires a larger sample than go, no-go gaging does.
Answer: B
NEW QUESTION 65
Which of the following quality system provisions is of the greatest concern when preparing an audit checklist for a vendor qualification system audit?
- A. Makeup of the MRB
- B. Drawing and print control.
- C. Calibration of test equipment.
- D. Training level of inspectors.
Answer: C
NEW QUESTION 66
Which of the following list of basic NDT techniques are X ray types?
- A. Electromagnetic / Thermal.
- B. Ultrasonic / Optical.
- C. Radiation / Image generation.
- D. Thermal / Radiation.
Answer: C
NEW QUESTION 67
What is the standard deviation of the following data?
3.2, 3.1, 3.3, 3.3, 3.1
- A. 0.0498
- B. 0.1
- C. 0.0894
- D. 3.2
Answer: C
NEW QUESTION 68
Which of the following are the MOST logical reasons for providing source inspection?
. The supplier has consistently shown poor out-going quality.
. The key inspection points are hidden after assembly at the suppliers' plant.
. The supplier requests the inspection to save them potential shipping expenses.
. The criticality of the product warrants it.
- A. I,IIandIVonly
- B. II,IIIandIVonly
- C. IIandIVonly
- D. I,II,IIIandIV
Answer: D
NEW QUESTION 69
You have been asked to sample a lot of 500 units from vendor whose past quality has been about 2% defective. A sample of 40 pieces is drawn from the lot and you have been told to reject the lot if you find two or more parts defective. What is the probability of finding two or more parts defective?
- A. 0.809
- B. 0.953
- C. 0.047
- D. 0.191
Answer: D
NEW QUESTION 70
An electronics firm was experiencing high rejections in their multiple connector manufacturing departments. "p" charts were introduced as part of a program to reduce defectives. Control limits were based on prior history, using the formula:
P' is the historical value of percent defective and n is the number of pieces inspected each week. After six weeks, the following record was accumulated
1,000 pieces were inspected each week in each department. Which department(s) exhibited a point or points out of control during this period (round off calculations to nearest tenth of a percentage point)?
- A. Department 104.
- B. Department 106.
- C. All of the department.
- D. Department 105.
Answer: C
NEW QUESTION 71
The existence of a quality control manual at your key supplier means
- A. That the firm is quality conscious.
- B. That a quality system has been developed.
- C. That the firm is a certified supplier.
- D. That a quality system has been implemented.
Answer: B
NEW QUESTION 72
Which table should be used to determine a confidence interval on the mean when standard deviation is NOT known and the sample size is 10?
- A. Chi-Square
- B. t
- C. z
- D. F
Answer: B
NEW QUESTION 73
A process is turning out end items that have defects of type A or type B or both. If the probability of type A defect is 0.1 and of a type B is 0.2, the probability that an end item will have no defect is
- A. 0.30
- B. 0.7
- C. 0.68
- D. 0.72
Answer: D
NEW QUESTION 74
If a sample size of 16 yields an average of 12 and standard deviation of 3, estimate the 95% confidence interval for the population (assume a normal distribution).
- A. Option B
- B. Option C
- C. Option D
- D. Option A
Answer: D
NEW QUESTION 75
Which of the following distributions models events that have 2 possibilities on each trial?
- A. Poisson.
- B. gamma.
- C. Normal.
- D. Binomial
Answer: D
NEW QUESTION 76
What order do the following corrective action steps normally take for nonconforming product?
. Analyze the problem.
. Assign responsibility.
. Take preventive action.
. Evaluate potential importance.
. Investigate possible causes.
- A. V,II,IV,I,III
- B. II,IV, V,I,III
- C. I,II,V,IV,III
- D. II,I,IV, V,III
Answer: B
NEW QUESTION 77
The "least squares method" is used in
- A. The central limit theorem
- B. Calculating σ2
- C. Calculating a best fit regression line.
- D. 2
Calculating σ and s2
Answer: C
NEW QUESTION 78
If a distribution is skewed to the left, the median will always be
- A. Between the mean and the mode.
- B. An average of the mean and the mode.
- C. Less than the mean.
- D. Greater than the mode.
Answer: A
NEW QUESTION 79
Inspection operations typically
- A. Help in assuring satisfactory quality.
- B. Occur between all manufacturing operators.
- C. Require precise equipment in most instances.
- D. Reduce the usability of the product or service involved.
Answer: A
NEW QUESTION 80
What distribution is used to determine the OC curve for an attributes sampling plan?
- A. Binomial.
- B. The binomial or the hypergeometric distribution.
- C. Exponential.
- D. Normal.
Answer: B
NEW QUESTION 81
A system was designed with 3 capacitors. When the system is first activated all capacitors are operating. The system continues to operate as long as at least 1 capacitor is operating. This is an example of
- A. A series system.
- B. An active parallel system.
- C. A standby parallel system.
- D. Redundancy.
Answer: B
NEW QUESTION 82
The term "quality audit" can refer to the appraisal of the quality system of
I. An entire plant or company.
II. One product.
III. One major quality activity.
- A. II and III only
- B. I and III only
- C. I only
- D. I, II and III
Answer: D
Explanation:
Explanation/Reference:
NEW QUESTION 83
The existence of a quality control manual at your key supplier means
- A. That the firm is quality conscious.
- B. That a quality system has been developed.
- C. That the firm is a certified supplier.
- D. That a quality system has been implemented.
Answer: B
NEW QUESTION 84
Which of the following quality gurus was very critical of merit-pay and individual bonuses?
He discouraged management by objectives and the ranking of employees by performance.
- A. Dr. Taguchi
- B. Dr. Deming
- C. Dr. Feigenbaum
- D. Dr. Juran
Answer: B
NEW QUESTION 85
The power of efficiency in designed experiments lies in the
- A. The large number of possible combinations of factors.
- B. Random order of performance.
- C. Hidden replication.
- D. The sequential and cyclical procedure of conjecture to design to analysis and back to conjecture.
Answer: C
NEW QUESTION 86
......
Use Valid New CQE Test Notes & CQE Valid Exam Guide: https://www.exam4tests.com/CQE-valid-braindumps.html
CQE exam torrent ASQ study guide: https://drive.google.com/open?id=1QnXFJ2H_zLA7hsi3n_zZ-VwsXB6HeyNi