[Aug-2021] Updated ASQ Certification CQE Exam Questions BUNDLE PACK
Master The ASQ Content CQE EXAM DUMPS WITH GUARANTEED SUCCESS!
NEW QUESTION 71
A single sampling plan calls for a sample size of 80 with an acceptance number of five and a rejection number of six If the quality of the submitted lots 10 percent defective. then the percent of lots expected to be accepted in the long run is approximately.
- A. 20%
- B. 30%
- C. 10%
- D. 6%
Answer: A
NEW QUESTION 72
During the performance of an audit, which of the following are key considerations?
I. What sampling plans may be necessary?
II. Is the audit schedule progressing as planned?
III. Is there a need for a technical specialist?
IV. Is the level of compliance satisfactory?
- A. II and IV only
- B. I, II, III and IV
- C. I, II and III only
- D. I and IV only
Answer: A
NEW QUESTION 73
The primary advantage of the Latin square design, compared to the factorial design, is that
- A. It allows higher significance levels.
- B. It eliminates the need for interaction analysis.
- C. In most circumstances, it requires less data.
- D. It does not require homogeneity of variance.
Answer: C
NEW QUESTION 74
A process has been experiencing problems lately. The operators charting the process have identified the cause to be due to a change in incoming materials. This problem is
- A. A special cause.
- B. A common cause.
- C. Attributed to purchasing.
- D. A normal event.
Answer: A
NEW QUESTION 75
A "p" chart
- A. Plots the number of defects in a sample.
- B. Can be used for only one type of defect per chart.
- C. Plots variations in dimensions.
- D. Plots either the fraction or percent defective in order of time.
Answer: D
NEW QUESTION 76
If a distribution is skewed to the left, the median will always be
- A. Greater than the mode.
- B. Between the mean and the mode.
- C. Less than the mean.
- D. An average of the mean and the mode.
Answer: B
NEW QUESTION 77
An X-bar and R chart with n=5 has been plotted for some time and has demonstrated random variation. Upon review of the last 30 plot points, the expected number of runs around the centerline on the X-bar chart is expected to be approximately which of the following?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION 78
The value for t, when making a two-tailed paired t test, with samples of 13 and alpha =0.05, is
- A. 2.179
- B. 1.782
- C. 1.711
- D. 2.064
Answer: A
NEW QUESTION 79
Of the services listed below, which one performed by design engineering is of particular interest to QA personnel?
- A. Audit reports.
- B. Change action.
- C. Cost reports.
- D. Rework criteria.
Answer: B
NEW QUESTION 80
Which of the following actions or techniques is MOST useful in determining the original fundamental cause of a product or process nonconformance?
- A. Pareto analysis.
- B. Continuous improvement.
- C. Preventive action.
- D. Root cause analysis.
Answer: D
NEW QUESTION 81
When used together for variables data, which of the following pair is the MOST useful in preparing control charts?
- A. R, sigma
- B. AQL, p-bar
- C. p, n
- D. X-bar and R
Answer: D
NEW QUESTION 82
Which of the following distributions have the set of all real numbers as their domain?
- A. None of the above.
- B. Lognormal
- C. Weibull
- D. Exponential
Answer: A
NEW QUESTION 83
The distribution of a characteristic is negatively skewed. The sampling distribution of the mean for large samples is:
- A. Lognormal.
- B. Negatively skewed.
- C. Positively skewed.
- D. Approximately normal.
Answer: D
NEW QUESTION 84
Of the services listed below, which one performed by design engineering is of particular interest to QA personnel?
- A. Audit reports.
- B. Change action.
- C. Cost reports.
- D. Rework criteria.
Answer: B
NEW QUESTION 85
An improvement in quality costs is MOST clearly indicated when:
- A. Total quality costs fall below 15% of total sales.
- B. Prevention costs increase.
- C. Appraisal and failure costs drop.
- D. Management objectives are met.
Answer: D
NEW QUESTION 86
As the scatter of points about a regression line becomes less, r2 will
- A. Become smaller.
- B. Be unaffected.
- C. Become larger.
- D. Approach a value of 1.
Answer: D
NEW QUESTION 87
When using a control chart, a point plotting within the limits on the chart is
- A. The equivalent of type II error.
- B. The equivalent of accepting the hypothesis that the process is in control.
- C. The equivalent of not rejecting the hypothesis that the process is in control.
- D. The equivalent of type I error.
Answer: C
Explanation:
Explanation/Reference:
NEW QUESTION 88
A vendor may be audited both before and during the execution of a contract. During such a vendor
audit, the focus may be directed at the management and resource management of the company. Which of the following areas would be EXCLUDED during such an audit?
- A. Design and process capabilities.
- B. Defined quality responsibilities.
- C. Company philosophy and organizational charts.
- D. Use and planning of time, manpower and training.
Answer: A
NEW QUESTION 89
Which of the following statements describes discrete data?
- A. The flight arrived at 9:08 PM.
- B. There were 5,923 gallons of fuel consumed on the flight.
- C. It takes 3 hours 48 minutes to fly from LA to New York.
- D. Of 225 people on the airplane, 85 had connecting flights.
Answer: D
NEW QUESTION 90
An electronics firm was experiencing high rejections in their multiple connector manufacturing departments. "p" charts were introduced as part of a program to reduce defectives. Control limits were based on prior history, using the formula:
P' is the historical value of percent defective and n is the number of pieces inspected each week. After six weeks, the following record was accumulated
1,000 pieces were inspected each week in each department. Which department(s) exhibited a point or points out of control during this period (round off calculations to nearest tenth of a percentage point)?
- A. Department 105.
- B. All of the department.
- C. Department 106.
- D. Department 104.
Answer: B
NEW QUESTION 91
An audit will be viewed as a constructive service to the function which is audited when it
- A. Furnishes enough detailed facts so the necessary action can be determined.
- B. Is general enough to permit managerial intervention.
- C. Is conducted by nontechnical auditors.
- D. Proposes corrective action for each item uncovered.
Answer: A
NEW QUESTION 92
The basic elements of an ultrasonic test systems do NOT include which of the following?
- A. An electronic system.
- B. A laser beam.
- C. A transducer.
- D. A test object.
Answer: B
NEW QUESTION 93
A bin contains 40 pills with a weight of 3.1 gm. each, 30 pills weighing 3.2 gms each and 10 pills weighing 3.3 gms each. The weight of an average pill is found from
- A. Option A
- B. Option D
- C. Option B
- D. Option C
Answer: B
NEW QUESTION 94
Which of the following nondestructive testing methods can be used to evaluate sub-surface discontinuities in aluminum bar stock?
I. Microwave.
II. Magnetic particle.
III. Pulse echo.
IV. Eddy current.
- A. I and III only
- B. I and IV only
- C. III and IV only
- D. I, II and IV only
Answer: C
NEW QUESTION 95
......
Pass ASQ CQE Exam – Experts Are Here To Help You: https://www.exam4tests.com/CQE-valid-braindumps.html
Get Latest ASQ Certification CQE Practice Test For Quick Preparation: https://drive.google.com/open?id=18qKK_W0MXby7jd7SuVJr-6sY6R4_1z7i